MODULES BSL, BENCH

Module for reprogramming ECU Bosch MEDC17 TC17XX BENCH (J2534)

Functions:
Read FLASH
Write FLASH
Read EEPROM
Write EEPROM

Identification
Checksum Correction

ECU Password Auto-Detection
Processor Type Auto-Detection

Additional Immobilizer OFF function, BOSCH EDC17/MED17 ECU
Additional T-Prot OFF function, BOSCH EDC17/MED17 ECU


The module is designed for reading and writing ECUs on a bench, without opening the ECU.

The module can only operate with a direct connection to the ECU using the J2534 Scanmatic 2/2Pro.

Procedure for working with the ECU:
Remove the ECU from car.
Connect the ECU on bench.
Perform the necessary operations (reads and writes).
Install the ECU in car.
Connecting to the ECU:

Connection to the ECU requires signals from the J2534 adapter (CAN-H = 6Pin, CAN-L = 14Pin, GPT1 = 1Pin, GPT2 = 2Pin, L-Line = 15Pin).
A 120 Ohm resistor is required between the CAN-H and CAN-L signals.

The L-Line is used to control the automatic power supply.




ECUFLASH TOOL is a program designed for working with electronic units in Volkswagen, Skoda, Ford, Mazda, Mitsubishi, Nissan/Infiniti, Subaru, Honda/Acura, Hyundai/Kia, Renault, Toyota/Lexus, Citroen/Peugeot, and other vehicles.

To work with the Program, you need a J2534 adapter, such as OpenPort 2.0, Mongoose, CarDaq, Scanmatic 2, Scanmatic 3, Chipsoft.

The software is delivered modularly. A SenseLock key is used to protect the software. If you don't have a USB key, you must purchase USB key, as the module will not function without one. If you have a USB key, please enter USB key number when placing your order.

Module for reprogramming Infineon Tricore BSL - TC1724/TC1738/TC1762/TC1766/TC1767/TC1791/TC1793/TC1796/TC1797/TC1798 - boot mode.

Functions:
Read FLASH
Write FLASH
Read EEPROM
Write EEPROM

TC1791-384 INT FLASH 3072kb
TC1791-384 EEPROM
TC1791-512 INT FLASH 4096kb
TC1791-512 EEPROM
TC1762 INT FLASH
TC1762 EEPROM
TC1766 INT FLASH
TC1766 EEPROM
TC1738 INT FLASH
TC1738 EEPROM
TC1767 INT FLASH
TC1767 EEPROM
TC1796 INT FLASH
TC1796 INT FLASH + EXT FLASH
TC1796 EXT FLASH
TC1796 EEPROM
TC1797 INT FLASH
TC1797 EEPROM
TC1724 INT FLASH
TC1724 EEPROM
TC1728 INT FLASH
TC1728 EEPROM
TC1782 INT FLASH
TC1782 EEPROM
TC1784 INT FLASH
TC1784 EEPROM

TC1792 INT FLASH (TEST)
TC1792 EEPROM (TEST)
TC1793 INT FLASH
TC1793 EEPROM
TC1798 INT FLASH
TC1798 EEPROM

Additional Immo OFF function, BOSCH EDC17/MED17 ECUs.
Additional T-Prot OFF function, BOSCH EDC17/MED17 ECU.
Works with external VAG eeprom, SIMOS PCR2.1 Tricore TC1796, Read/Write AT25640 eeprom, Unlock.

Read Password:
Nissan, Renault, Mersedes ecu Siemens Continental SID309, SID310, EMS3155.
PSA ecu Siemens Continental SID208.
Ducati Bosch ME17.9.21 TriCore TC1724.
Chery/Great Wall/Lifan Bosch ME17 (ME17.8.8)
Chrysler, Dodge, Jeep ecu BOSCH GPT.
Nissan, Renault ecu BOSCH GPT.
BMW, ecu BOSCH GPT.
MERSEDES, ecu BOSCH GPT.
VOLVO, ecu BOSCH GPT.
Ford, ecu BOSCH GPT.
JAGUAR, ecu BOSCH GPT.
Range Rover, ecu BOSCH GPT.
Volkswagen, Skoda, Seat, Audi, VAG, ecu BOSCH GPT Ver.1
Volkswagen, Skoda, Seat, Audi, VAG, ecu BOSCH GPT Ver.2
Ford, Mazda ecu Siemens Continental EMS2204, EMS2207, EMS2211.
Ford, Mazda ecu Siemens Continental SID208, SID209, SID807.
JLR LandRover ecu Siemens Continental SID208.
Kia, Hyundai, SsangYong ecu Siemens SIM2K-2XX.
Volkswagen, Skoda, Seat, Audi, VAG, ecu BOSCH TPROT 8+.
Kia, Hyundai, ecu BOSCH TPROT 8+.
UAZ, VAZ Bosch ME17.9.71 TriCore TC1724.
GM, Opel, Chevrolet ecu BOSCH GPT

GPT adapter is purchased separately.



ECUFLASH TOOL is a program designed for working with electronic units in Volkswagen, Skoda, Ford, Mazda, Mitsubishi, Nissan/Infiniti, Subaru, Honda/Acura, Hyundai/Kia, Renault, Toyota/Lexus, Citroen/Peugeot, and other vehicles.

To work with the Program, you need a J2534 adapter, such as OpenPort 2.0, Mongoose, CarDaq, Scanmatic 2, Scanmatic 3, Chipsoft.

The software is delivered modularly. A SenseLock key is used to protect the software. If you don't have a USB key, you must purchase USB key, as the module will not function without one. If you have a USB key, please enter USB key number when placing your order.

Module for reprogramming ECU POWERPC BSL CAN BUS MCU SPC5673/SPC5674

POWERPC BSL CAN BUS- SPC5673/SPC5674 - boot mode 40Mhz.
POWERPC BSL CAN BUS- SPC5673/SPC5674 - boot mode 8Mhz.

Functions:
Read FULL FLASH
Write FULL FLASH
Read SHADOW FLASH
Write SHADOW FLASH (This feature is disabled for security reasons)

Approximate list of cars:

ISUZU ECU DELPHI DCM6.2AP SPC5674
GreatWall ECU DELPHI DCM6.2AP SPC5673
JAC ECU DELPHI DCM6.2AP SPC5674
SsangYong ECU DELPHI DCM6.2AP SPC5674
Hyundai, Kia ECU DELPHI DCM6.2AP SPC5674
Peugeot, Citroen ECU PSA DELPHI DCM6.2AP SPC5674
Peugeot, Citroen ECU PSA DELPHI DCM6.2C SPC5674
Toyota DELPHI DCM6.2AP SPC5674
GM DELPHI DCM6.2AP SPC5674
GM DELPHI DCM6.2C SPC5674
GM DELCO GEN1 E98 SPC5674
GM DELCO GEN2 E98 SPC5674
GM DELCO GEN1 E92 SPC5674
GM DELCO GEN2 E92 SPC5674
VAG ECU DELPHI DCM6.2V SPC5674 (the ECU is password protected, the password must be read by the OBD2 module).




ECUFLASH TOOL is a program designed for working with electronic units in Volkswagen, Skoda, Ford, Mazda, Mitsubishi, Nissan/Infiniti, Subaru, Honda/Acura, Hyundai/Kia, Renault, Toyota/Lexus, Citroen/Peugeot, and other vehicles.

To work with the Program, you need a J2534 adapter, such as OpenPort 2.0, Mongoose, CarDaq, Scanmatic 2, Scanmatic 3, Chipsoft.

The software is delivered modularly. A SenseLock key is used to protect the software. If you don't have a USB key, you must purchase USB key, as the module will not function without one. If you have a USB key, please enter USB key number when placing your order.

Module for reprogramming ECU POWERPC BSL CAN BUS MCU MPC55XX

POWERPC BSL CAN BUS- MPC55XX - boot mode 8Mhz.

Functions:
Read FULL FLASH
Write FULL FLASH
Read SHADOW FLASH
Write SHADOW FLASH (This feature is disabled for security reasons)
Identification

Approximate list support MCU:

MPC5553
MPC5554
MPC5561
MPC5562
MPC5565
MPC5566
MPC5567
MPC5533
MPC5534
MPC5516




ECUFLASH TOOL is a program designed for working with electronic units in Volkswagen, Skoda, Ford, Mazda, Mitsubishi, Nissan/Infiniti, Subaru, Honda/Acura, Hyundai/Kia, Renault, Toyota/Lexus, Citroen/Peugeot, and other vehicles.

To work with the Program, you need a J2534 adapter, such as OpenPort 2.0, Mongoose, CarDaq, Scanmatic 2, Scanmatic 3, Chipsoft.

The software is delivered modularly. A SenseLock key is used to protect the software. If you don't have a USB key, you must purchase USB key, as the module will not function without one. If you have a USB key, please enter USB key number when placing your order.

Module for reprogramming ECU POWERPC BSL CAN BUS MCU MPC56XX

POWERPC BSL CAN BUS- MPC56XX - boot mode 8Mhz.

Functions:
Read FULL FLASH
Write FULL FLASH
Read SHADOW FLASH
Write SHADOW FLASH (This feature is disabled for security reasons)
Identification

Approximate list support MCU:

SPC5633M/MPC5633M
SPC5634M/MPC5634M




ECUFLASH TOOL is a program designed for working with electronic units in Volkswagen, Skoda, Ford, Mazda, Mitsubishi, Nissan/Infiniti, Subaru, Honda/Acura, Hyundai/Kia, Renault, Toyota/Lexus, Citroen/Peugeot, and other vehicles.

To work with the Program, you need a J2534 adapter, such as OpenPort 2.0, Mongoose, CarDaq, Scanmatic 2, Scanmatic 3, Chipsoft.

The software is delivered modularly. A SenseLock key is used to protect the software. If you don't have a USB key, you must purchase USB key, as the module will not function without one. If you have a USB key, please enter USB key number when placing your order.

Module for reprogramming ECU Bosch MEDC16 POWERPC MPC BENCH (J2534)

Module: ECU Bosch MEDC16 POWERPC MPC BENCH (J2534) K-LINE

Functions:
Read FLASH INTERNAL
Write FLASH INTERNAL
Read FLASH EXTERNAL
Write FLASH EXTERNAL
Read EEPROM
Write EEPROM
Identification
Checksum Correction
Processor Type Auto-Detection

The module is designed for reading and writing ECUs on a bench, without opening the ECU.
The module can only operate with a direct connection to the ECU using the J2534 Scanmatic 2/2Pro/3.
The L-Line is used to control the automatic power supply.




ECUFLASH TOOL is a program designed for working with electronic units in Volkswagen, Skoda, Ford, Mazda, Mitsubishi, Nissan/Infiniti, Subaru, Honda/Acura, Hyundai/Kia, Renault, Toyota/Lexus, Citroen/Peugeot, and other vehicles.

To work with the Program, you need a J2534 adapter, such as OpenPort 2.0, Mongoose, CarDaq, Scanmatic 2, Scanmatic 3, Chipsoft.

The software is delivered modularly. A SenseLock key is used to protect the software. If you don't have a USB key, you must purchase USB key, as the module will not function without one. If you have a USB key, please enter USB key number when placing your order.